Polycom RMX DOC2548A Manual de usuario

Polycom RMX™ 4000 Hardware GuideVersion 6.0 | April 2010 | DOC2548A

Chapter 1- Hardware Description1-4MPM+ Resource CapacitiesThree MPM+ card assemblies are available: MPM+ 80, MPM+ 40 and MPM+ 20 offering various reso

Polycom RMX 4000 Hardware Guide1-5Table 1-4 summarizes the resource capacities of the various video resource types in an RMX containing MPM+ cards. I

Chapter 1- Hardware Description1-6Safety RequirementsThis section describes the requirements your site must meet for safe installation and operation o

Polycom RMX 4000 Hardware Guide1-7General Installation Precautions• Use a regulating uninterruptable power supply (UPS) to protect the RMX 4000 from p

Chapter 1- Hardware Description1-8• Always keep the rack’s trays and card’s slots closed when not servicing, to maintain proper cooling.Installing the

Polycom RMX 4000 Hardware Guide1-9Make sure that boxes contain all the required parts.4 Remove the boxes and top Stratocell®.5 Holding the handle on e

Chapter 1- Hardware Description1-10Installing the RMX in a Rack or as a StandaloneEither place the RMX 4000 on a hard, flat surface such as a desktop

Polycom RMX 4000 Hardware Guide1-11Placing the RMX 4000 in a 19” Rack1 When the RMX is to be rack mounted chassis runners must be installed on the rac

Chapter 1- Hardware Description1-123 Fasten the RMX to the rack with 8 screws into the holes provided on the RMX’s front as shown in Figure 1-3.Figure

Polycom RMX 4000 Hardware Guide1-13Placing the RMX 4000 in a 23” Rack1 Mounting the RMX 4000 on a 23” rack requires that first the handles and then th

Trademark InformationPolycom®, the Polycom “Triangles” logo, and the names and marks associated with Polycom’s products are trademarks and/or service

Chapter 1- Hardware Description1-14The airflow of the RMX 4000 is from right to left. Be sure that the areas on the left and right side of the system

Polycom RMX 4000 Hardware Guide1-153 Place the RMX in a rack and tighten the 8 screws securing the RMX to the rack.Connecting the RMX 4000 to Power So

Chapter 1- Hardware Description1-16• Listed fastening hardware must be compatible with the materials being joined and must be preclude loosening, dete

Polycom RMX 4000 Hardware Guide1-17Connecting the RMX 4000 to -48DC SELV Power1 On the DC Power Rail Modules (PRM’s), set the two circuit breakers to

Chapter 1- Hardware Description1-185 Connect the green or green-yellow wire to the system single-point M6x15 “Ground” bolt.If the unit is rack mounted

Polycom RMX 4000 Hardware Guide1-19Connecting Cables on the RMX 4000To connect the cables (AC and DC systems):• RTM-IP 4000:— Connect the Management N

Chapter 1- Hardware Description1-20For more information about specific card connections, see:• "RTM-IP 4000” on page 1-34• "RTM ISDN” on pag

Polycom RMX 4000 Hardware Guide1-21RMX 4000 ComponentsOn the RMX 4000 components are located on both the front and rear of the MCU as listed in Table

Chapter 1- Hardware Description1-22Figure 1-8 shows the front panel of an RMX 4000 DC system.Figure 1-8 RMX 4000 DC Front ViewTable 1-7 Polycom RMX

Polycom RMX 4000 Hardware Guide1-23AC/DC Power Supply ModulesThe AC Power Supply drawers are located below the MPM+ Cards and are connected to the bac

CE MARK R&RTTE DirectiveČesky [Czech]: Polycom (UK) Ltd tímto prohlašuje, že tento RMX 4000 je ve shodě se základními požadavky a dalšími příslušn

Chapter 1- Hardware Description1-24RMX 4000 Rear PanelThe RMX 4000 rear panel contains the RTM-IP 4000 card and either (or both) RTM ISDN/RTM LAN card

Polycom RMX 4000 Hardware Guide1-25Figure 1-10 RMX 4000 DC Rear ViewRTM-IP 4000A single RTM-IP 4000 card provides system management based on the ATCA

Chapter 1- Hardware Description1-26Figure 1-11 RMX 4000 RTM-IP 4000 Rear Panel LayoutThe following items appear on the RMX 4000 rear panel:LAN 6- 10/1

Polycom RMX 4000 Hardware Guide1-27RTM ISDNThe RTM ISDN card connects directly to an MPM+. The RTM ISDN card routes data between the MPM+ cards and co

Chapter 1- Hardware Description1-28ISDN/PSTN Clock SourceEach RTM ISDN card has its own primary and secondary clock source. The first span to synchron

Polycom RMX 4000 Hardware Guide1-29DC Power Rail ModuleA DC power rail module includes a power inlet, circuit breaker, EMI filter and backplane connec

Chapter 1- Hardware Description1-3012 Fan Drawer Mandatory13-16 RTM ISDN/RTM LANEither an RTM ISDN or an RTM LAN card is mandatory in combination with

Polycom RMX 4000 Hardware Guide1-31RMX 4000 LEDsThe RMX includes LEDs located on the front panel and rear panel. In the front panel, the LEDs reflect

Chapter 1- Hardware Description1-32Fabric Switch Module (FSM 4000)ERR Red ON - Major error on card.Flashes - During card startup.RDY Green ON - The ca

Polycom RMX 4000 Hardware Guide1-33CNTL 4000 Unit ERR Red ON - Major system error. In case of an active alarm this light is ON, and the RDY green is O

Polski [Polish]: Niniejszym Polycom (UK) Ltd oświadcza, że RMX 4000 jest zgodne z zasadniczymi wymaganiami oraz innymi stosownymi postanowieniami Dyre

Chapter 1- Hardware Description1-34RMX 4000 Rear Panel LEDsRTM-IP 4000The following LEDs appear on the RTM-IP 4000 card:Table 1-11 RMX 4000 RTM-IP 40

Polycom RMX 4000 Hardware Guide1-35RTM LANThe following LEDs appear on the RTM LAN:ShMG (Shelf Manager) LEDsERR Red ON - Major error on RTM-IP 4000 ca

Chapter 1- Hardware Description1-36RTM ISDNThe following LEDs appear on the RTM ISDN:Table 1-13 RMX 4000 RTM ISDN LEDs Function NameLED NameLED Color

2Component ReplacementThe RMX 4000 is designed with ease of maintenance in mind. Most components are swappable and are accessible directly via the fro

Chapter 2- Component Replacement2-2• Fabric Switch Module (FSM 4000), see “Replacing the Fabric Switch Module (FSM 4000)” on page 2-18.Before replacin

Polycom RMX 4000 Hardware Guide2-3Using the Modified PMC Compatible Ejector LeverOn the RMX 4000 most components are fitted with identical ejector lev

Chapter 2- Component Replacement2-4Replacing the CNTL 4000 ModuleThe CPU module is the management system of the RMX 4000. Use the following procedure

Polycom RMX 4000 Hardware Guide2-5Replacing an AC Power Supply ModuleTwo units supply power to the RMX 4000 (3rd optional - AC only), each unit with i

Chapter 2- Component Replacement2-63 Carefully slide the Power Supply unit out from the front slot.4 Slide in the replacement Power Supply unit.5 Pus

Polycom RMX 4000 Hardware Guide2-74 Carefully slide the PEM unit out from the rear slot.5 Slide in the replacement PEM unit.6 Push the PEM unit firml

Polycom RMX 4000 Hardware GuideiTable of ContentsHardware Description . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1Main Features ...

Chapter 2- Component Replacement2-84 Using a star screw driver, disconnect the two wires connected to the Terminal block (-48 VDC & RTN) of the fa

Polycom RMX 4000 Hardware Guide2-9Replacing the Fan DrawerEight fans are mounted in the Fan drawer, where the airflow is from right to left. Should on

Chapter 2- Component Replacement2-10Inserting an Air Filter (Optional) in the Fan DrawerIn the fan drawer, an Air Filter can be added as an option. Yo

Polycom RMX 4000 Hardware Guide2-115 Open the filter tray, by unscrewing two screws on the tray.6 Insert the air filter into the filter tray.7 Close

Chapter 2- Component Replacement2-122 Power down the card by partially opening the ejector levers until the blue HS LED on the card and the Control Un

Polycom RMX 4000 Hardware Guide2-135 Carefully slide the MPM+ card out through the front panel.Installing the Replacement MPM+ Card1 On the card to be

Chapter 2- Component Replacement2-14Installing a New MPM+ Card in a Powered On RMX 40001 If applicable, loosen the captive screws and remove the slot

Polycom RMX 4000 Hardware Guide2-155 On the card to be installed, move the ejector levers to their fully open position.6 Slide in the replacement RTM

Chapter 2- Component Replacement2-16Replacing the RTM-IP 4000The RTM-IP 4000 card on the rear of the RMX 4000 provides connectivity to all the MCU mod

Polycom RMX 4000 Hardware Guide2-17Replacing the RTM LANThe RTM LAN card on the rear of the RMX 4000 provides connectivity to all the MCU modules. Use

Table of ContentsiiDC Power Rail Module ... 1-29Component Slot Allocation ...

Chapter 2- Component Replacement2-18Replacing the Fabric Switch Module (FSM 4000)1 Ensure that the power switch/circuit switch on the RMX 4000 is turn

1Hardware DescriptionThis Hardware Guide provides information on the RMX 4000 and its components. This system utilizes a modular “universal slot” plat

Chapter 1- Hardware Description1-2RMX 4000 SpecificationsTable 1-1 Polycom RMX 4000 Specifications PhysicalHeight 6U (26.56 cm.)Width 19” (48.26 cm.)

Polycom RMX 4000 Hardware Guide1-3System CapacitiesThe following table summarizes the different system capacities.Storage temperature -40°– 70°C (40°–